Best Compound Miter Saw 2019 – Guide and Reviews
Table of Contents
- Best Compound Miter Saw Comparison
- 5 Best Compound Miter Saw Reviews
- 1. DEWALT DWS709 Slide Compound Saw
- 2. Bosch 5312 12-Inch Dual Miter Saw
- 3. Makita LS1216L 12-Inch Dual Slide Miter Saw
- 4. DEWALT DWS780 12-Inch Double Saw
- 5. Hitachi C10FCH2 15-Amp 10-inch Saw Single Bevel compound
- Final Verdict
- Relevant Resources
Looking for the best compound miter saw? what about if it is a dual compound sliding miter saw? With this additional features, you will get more versatility which will ease your projects. Here are the reviews of your top 5 options. Just how do you pick the best miter saw for your woodcutting workshop?
It’s not enough that you get a miter saw with sliding features so you can work on larger work pieces.You also need one with dual compound capabilities, so you can make miter and bevel cuts at the same time.
With the dual compound sliding miter saw, woodcutting projects such as working with crown molding becomes so much easier that you may have thought. Choosing the best one for you may not be easy at first, since you have so many options. To make your life easier, here are 5 of the best choices you can pick for your woodcutting projects:
Best Compound Miter Saw Comparison
5 Best Compound Miter Saw Reviews
1. DEWALT DWS709 Slide Compound Saw
Dewalt DWS709 is a bit expensive, but then again you’re paying to get the dependable Dewalt quality. Here you have a powerful 15-amp motor that gets the 12-inch blade going at 3,800 rpm. That really ought to make short work out of various woodcutting projects. This offers dual miter and bevel cutting capacity.
The sliding fences can accommodate 5.5-inch crown molding along with 4.5-inch base molding. When it’s time to make your bevel cuts, you can just slide the fences out of the way. You can cut through lumber measuring 2 by 14 inches at 90 degrees. At 45 degrees, you can still cut through lumber measuring 2 by 10 inches.
With miter cuts, you can work with angles up to 60 degrees to the right and 50 degrees to the left. You only need to set it to any of the 13 different miter detents preset on the scales. That should be easy, since the miter and the bevel scales are very easy to read and you have a large red miter pointer.
Accuracy for your repetitive cuts won’t be a problem with these scales and detents, and you also have dual horizontal steel rails with linear ball bearings for even greater accuracy. Wear and tear isn’t really a problem with the dewalt DWS709, as it features pads on the stainless steel that minimizes the damage you normal get over time. That’s probably why it has a 3-year warranty.
With the heavy duty aluminum base, the dual compound miter saw is also quite strong and rigid. But it’s also very portable, since the design is compact and the weight is only 51 pounds.
2. Bosch 5312 12-Inch Dual Miter Saw
We’ve all heard about the traditional excellence of German engineering, and the Bosch brand is a perfect example of Teutonic expertise. Bosch has been around for more than a century, and the Bosch 5312 is a good showcase of just how good a miter saw can get.
Here you have a 15-amp motor powerful enough for many types of work pieces. You’re going to need that power, since the design and the extensions allow you to work on pieces with a total length of 40 inches. Making bevel cuts is easy, as the bevel scales are very easy to read. You can just set it to any of the commonly used angles, with stops at 0, 33.9, and 45 degrees. Just turn the range selector knob and secure it with the bevel lock lever.
With the 4.5-inch speed track sliding fences, you’ll surely find it easy to work on crown molding.For your miter cuts, you have an angle range of up to 52 degrees to the left and 60 degrees to the right. You can just pick on any of the miter detents preset at 0, 15, 22.5, 31.6, and 45 degrees, with an extra detent at 60 degrees to the right.
If these presets aren’t enough, you can still choose another angle with the miter detent override. This dual capability makes it very easy to make repetitive cuts accurately. You can do it quickly too, since the Bosch 5312 features an electric brake that stops the blade from spinning almost immediately. Your cuts should be smooth and easy, as the 12-inch blade it comes with is already great. It can stay sharp for a good long while.
The warrant for this Bosch miter saw is for a standard 1 year, but don’t let that put you off.This is one durable miter saw which can provide you with quick and accurate cuts for a long time.
3. Makita LS1216L 12-Inch Dual Slide Miter Saw
This uses a 15-amp motor that doesn’t really require a lot of maintenance. But it’s powerful enough to get the 12-inch blade spinning at 3200 rpm. That should take care of your woodcutting needs, even if you’re dealing with tough hardwood.
It’s so powerful that even without any setup, you can cut through 15-inch wide boards at 90 degrees, and you can also cut through 4 by 16-inch beams. It offers advanced features including an innovative retractable guard system and advanced direct drive gearbox, so that you receive what’s arguably the best crown cutting and crosscutting in its class.
With Makita LS1216L, you’re able to deal with 8 inches of crown molding and 6.5 inches of baseboard.Don’t worry about the accuracy of the cuts, because it also features linear ball bearings and the special 4-steel rail sliding system for enhanced rigidity. You can also make lower and upper adjustments on the sliding fence system for even greater precision.
For bevel cuts, you can use the highly visible dual front bevel scales, any of the 4 positive stops for left and right, and the accessible bevel lock. For miter cuts, you have an angle range of up to 60 degrees to the right and 52 degrees to the left. There’s a one-touch design for the miter lock system, while you can’t miss the cut line with the built-in laser marker.
These are just some of the features that make the Makita LS1216L a pleasure to have in any woodcutting workshop. It may be a bit expensive, but it sure is extremely useful and convenient.
4. DEWALT DWS780 12-Inch Double Saw
Here’s another worthy contender for the best 12-inch miter saw in its class. It’s an expensive Dewalt, but then again you receive dependable Dewalt quality. For bevel cuts, the dewalt DWS780 goes up to 49 degrees to both the left and right, so you won’t need to flip the work piece if you have to make a bevel cut on the opposite cut.
Here you have preset stops on both sides, set at 0, 22.5, 33.9, 45, and 49 degrees.For miter cuts, your angle rage to the right reaches up to 50 degrees and to the left it’s 60 degrees. Now you even have 10 distinct preset detents to choose from, with a miter override incase the presets aren’t set to the angle you want. Cutting straight down lets you go through 2 by 16 inches of lumber work pieces.
At 45 degrees, you can also make crosscuts through 2 by 12-inch lumber. The horizontal cutting capacity is at 13⅞ inches, the vertical cutting capacity is at 6.75 inches, and the nested crown capacity is at 7.5 inches. The alignment system is so accurate you won’t need to recalibrate it after changing the blade or after an extended period of time.
You also have an LED light for more accurate cuts. The dust collection system is exceptional too. As for the durability, don’t worry. The warranty is for 3 years, and there’s also a year of free service.
5. Hitachi C10FCH2 15-Amp 10-inch Saw Single Bevel compound
This one is for those with limited budgets, and so you only get a single bevel feature on this dual compound miter saw. Still, the price is quite attractive considering the features you do get with hitachi C10FCH2. This 10-inch saw starts with a powerful 15-amp motor that can get the blade spinning at an impressive 5,000 rpm.
Here, the bevel cuts may only be up to 45 degrees to the left. But you do get adjustable bevel stops for the most common angles. As for miter cuts, your range reaches up to 52 degrees for both the left and right sides. You also get a laser marker to keep your cuts accurate. It’s very easy to use, as the elastomer handle minimizes the vibrations that reach your hand.
The dust collector system reduces the cleanup afterwards, and you even get carbon brushes for your saw. This 10-inch saw very portable too, as it weighs in at just 33 pounds. You won’t any other comparable miter saw that’s lighter. You also won’t find a warranty period that’s longer. With the Hitachi C10FCH2, the warranty is for 5 years.
As you can see, you still need to make some choices as to what features you need for your miter saw. Do you want one with a 12-inch blade, or will a 10-inch blade suffice? Are you willing to pay extra for a dual bevel compound miter saw, or will a single bevel suffice? Regardless of what you pick, it’s also likely that you won’t regret getting the best compound miter saw for your workshop. With it, working on crown molding and other woodcutting projects is easier, faster, and probably a lot more fun.