In the world of woodworking, there are a number of tools that can be used to cut out pieces for a project. It can be hard to figure out the difference between a jigsaw and a scroll saw. The two tools are similar, but they have some key differences. In this article, we are going to learn Jigsaw vs Scroll Saw.
Jigsaws are used for cutting curves or straight lines in wood with tough surfaces while scrolling saws are best for delicate pieces of work that require precision cuts.
Scrolling saws typically use blades that only cut on one side at a time, unlike the blade on a jigsaw which cuts on both sides simultaneously. Scroll saw blades also need to be changed more often due to their delicate nature and smaller size than those of the jigsaw blades.
Which Type of Saw is Better For You
If you are looking for a tool that will quickly cut tough surfaces, then the jigsaw is your best bet. Jigsaws typically have blades on both sides of the blade to make it easier when cutting curves or straight lines in wood and can be used with any type of surface material.
However, If you are looking for a tool that will cut delicate pieces of work, then the scroll saw is your best option. The scrolling blade needs to be changed less often than on the jigsaw because it cuts only one side at a time and has smaller blades so they’re more precise in their cutting abilities.
What does it do?
A jigsaw is a powerful tool that can be used on any type of surface material and works well for cutting curves or straight lines in the wood. The blade cuts both ways at the same time, which makes it easier to cut through difficult surfaces like tough woods or metal. Jigsaws work best when you need to make precision cuts.
A jigsaw is a type of saw that cuts with an oscillating blade. This tool will cut tough surfaces and curves or straight lines in wood for the perfect finish. The blades on either side are set at different angles, which creates the sawing motion.
The back edge of these blades comes together to form a continuous cutting line when the blade is in use. Jigsaws are typically used with non-ferrous metals, plastics, and other tough materials that require a lot of power to cut through them.
- The interface is simple to use
- Easily transportable
- They do not cut as cleanly as scroll saws
- It is messy
What does it do?
A scrolling saw is a type of saw that will cut delicate pieces of work. The blade on the scroll saw only cuts one side at a time, which makes it easier to be precise with your cutting abilities when you are using this tool. Scrolling blades also need to be changed more often than those of the jigsaw.
A scrolling saw cuts delicate pieces of work like those in woodworking. The blades only cut one side at a time, and they need to be changed more often than the jigsaw blade. Scrolling saws are best for intricate details that require precision cutting abilities; however, it is not recommended to use them on tough surfaces unlike using a jigsaw.
- Cuts that are clean, precise, and intricate
- The dust level is low
- Ideal for thinner woods
- It’s not portable to use a tabletop
Differences Between a Jigsaw and Scroll Saw
Which is the best saw? That’s the question on everyone’s mind. But is there a correct answer to that question? Jigsaws can use interchangeable and continuous blades, but scroll saws need blades specifically designed for them.
You’ll find scroll saws also tend to be less costly than jigsaws. Jigsaws and scroll saws also differ in the size of the work they can handle. Jigsaws tend to be larger because you can put bigger blades on them. They are also able to cut more material at once.
Scroll saws, on the other hand, are smaller and lighter. They are easier to control. However, you have to think in terms of your project. Are you going to cut a lot of material? If you are not sure, it is probably better to go with a jigsaw saw.
If you are going to use your jigsaw only for light woodwork, then a scroll saw is best. Many people prefer scroll saws because they can cut curves and intricate designs with ease. Also, most of them have very long blades, which cut better than short blades.
Why You Should Use One Over The Other
The jigsaw is best for cutting materials like wood, metal, and plastics. The scroll saw is great for projects that require intricate details that need precision cutting abilities; however, it’s not recommended to use them on tough surfaces. Jigsaws can use interchangeable blades whereas a scroll saw uses blades specifically designed for the tool so they are less costly.
Tips For Using Each Tool Correctly
Jigsaws are best for heavy-duty work. Scroll saws are best used on delicate and detail-oriented projects like those in woodworking; however, they shouldn’t be used on tough surfaces because the blades tend to break more often than those of a jigsaw.
If you’re looking at a scroll saw, don’t forget to think about the type of material you’re going to use it on. This will help you make an informed decision about the specific type of blade and other accessory tools that are needed to complete your project.
If you’re looking at a jigsaw, think about how often it’s going to be used before buying one in order to get the best value for money. You’ll also need to decide between corded or cordless.
If you’re looking at a scroll saw, think about how often it’s going to be used before buying one in order to get the best value. You’ll also need to decide between corded or cordless. This will help you make an informed decision about the specific type of blade and other accessory tools that
How to Clean Your Scroll Saw or Jigsaw Blade
Which method is better for cleaning your scroll saw blade: the bucket or wet rag? Is it easier to use a water hose, soap, and scrubber, or an abrasive cleaner with stiff bristles? If you’ve ever been stumped by this question, don’t worry.
Scroll Saws are designed in such a way that they can be cleaned quickly and easily using any of these methods — which one should you choose depends on what type of dirt is stuck onto the blade, how greasy it is (if at all) if there’s metal dust from cutting different metals before the last wash…
The water hose is a good choice for removing the largest amount of dirt and debris. It requires no chemicals, which means it’s safe to use anywhere from your garage floor to the car engine bay! A good way to get really tough grease off an already clean blade is with one or two drops of dish soap in boiling hot water.
This creates a soapy bubble that will only harm surfaces and not any human skin (always test on yourself before doing this!) Scrub extra hard if you’re dealing with stubborn stains – they might have been even more difficult had you waited too long.
If your jigsaw blade is dusty, clean it with a duster or brush. If the sawdust has dried to a crust on the blade surface and cannot be removed with your eyesight alone (even after you’ve tried brushing), use an air compressor to blow off loose dust particles from the outside of the tip area first. Afterward, gently use compressed air around inside corners for best results.
An alternative way would be using soap and water mixed well in a bowl. Put some kind of absorbent material such as a paper towel into this mixture then dip your hands into it – or simply wet them with a washcloth dipped in solution if so desired. The idea might sound unusual but trust me; just try doing these steps.
Why You Should Iinvest in Both Tools
Having a scroll saw and jigsaw available to you will enable you to take on more projects, which in turn gives your skills time to grow.
Plus, these two tools are so different from each other that it’s nearly impossible for them not to complement one another: if I had only the scroll saw but wanted to cut out shapes with precision or detail, then my jigsaw would really come in handy.
Or vice versa – cutting detailed curves is better suited for a scroll saw because they’re much easier when working at an angle; meanwhile, jigsaws do something similar by quickly removing material like plywood without needing any additional work done beforehand (though this “rough” cut doesn’t have as clean of results).
WEN 3921, 16-inch, Two-Direction Variable Speed
Our top pick. This 16-inch variable speed scroll saw from WEN is a great quality saw that works great for beginners. It is perfect to cut intricate patterns into wood or metal.
It has a 16-by-11-inch table with a bevel up to 45 degrees to the left that can be taken off to allow a longer workspace on whatever is being cut. It offers a great price and is extremely well made. This saw has extremely convenient onboard storage and even includes a dust port.
DEWALT DW788, 20-Inch, Variable-Speed
Our second Choice. This Dewalt scroll saw is very lightweight, measuring in at a mere 5.5 pounds, and is exceptionally compact. Because it is small, it is perfect for even small living spaces.
It is also extremely quiet while it is in use, which is excellent for apartments or condos. This tool is a great way to save money while working with more wood material than some other saws.
Delta Power Tools 40-694, 20 Inch, Variable Speed
Our third choice. The Delta Power Tools 40-694 20 inches. Variable Speed Scroll Saw is a must-have tool for those who plan to build wooden projects. The ergonomic design will allow you to get right into your project without worrying about taking up space in your workbench.
This scroll saw has lots of power and is the perfect tool for any professional who needs a powerful tool in their arsenal. It’s light enough for use indoors or out and is very easy to use.
BLACK+DECKER BDEJS600C, Smart Select, 5.0-Amp
The Black and Decker BDEJS600C is a fantastic choice for anyone looking for a high-quality tool to get everything done that needs to be done around the house. It has an 8.1-amp motor that generates 3,000 s/m of cutting power cut through even the toughest materials.
This high-performance electric jigsaw boasts a three-quarter-inch blade that cuts through wood, plastic, and sheet metal. This Jig Saw is perfect for homeowners who need to cut through traditional materials like 2x4s, 2x6s, and plywood. The powerful motor can cut through 2x4s and most other materials in a single pass with minimal effort.
DEWALT DCS334B, 20V MAX XR, Cordless
The Dewalt 20V Max XR Cordless Jig Saw is an excellent jigsaw for woodworking, remodeling, cutting metal, and other types of applications. It is a great tool for those on a budget who need a saw that can handle a lot of material at a time. The brushless motor delivers the perfect amount of power to cut through the plywood and multiple layers of particle board without clogging the blade.
With the Easy to Use 2-position lever, this tool is a breeze to set up and use. The 2-position, keyless blade change makes it easy to change the blade. In addition, the integrated dust blower helps to clear the work area while cutting.
RYOBI One+ P5231, 18V, Lithium-Ion Cordless, Orbital T-Shaped
This Ryobi One+ P5231 Cordless Orbital Jigsaw is an excellent addition to anyone looking for a jigsaw that will not let them down. This unit is durable, easy to use, and has incredible features like a trigger lock and a blade-saving base. In addition, this unit comes with an RYOBI 18V ONE+ LITHIUM BATTERY.
This jigsaw is ideal for small to medium size projects around the house or office. It cuts fast and has a built-in blower that will help keep the workspace free of debris.
Conclusion: Scroll saw Vs Jigsaw
Jigsaw vs Scroll Saw, Which do you use? Every project is different, which means that the right tool for a given task depends on what you are working with. If your goal is to make precise cuts and clean edges in materials such as wood or metal, then a jigsaw may be best for you.
However, if you need to cut intricate shapes out of many layers of material at once, then scroll sawing will likely offer better results than a jigsaw because it can create curves without having to retrace your steps over each layer as the jigsaw does.
When making this decision yourself, think about how much control do I want? How accurate am I going to have to be? What kind of surface am I cutting into (metal vs plastics)? These questions should help guide you to the perfect edge.